THIS IS A HIGH QUALITY CARBIDE TIP CLEANER TO CLEAN JET AND PASSAGES IN CARBURETORS, THIS IS A HIGH QUALITY CLEANER

CHAIN SAW FILE HOLSTER TO KEEP YOUR FILE WITH YOU WHEN YOU NEED TO SHARPEN THE CHAIN WHEN DULL, FASTEENS  ON THE BELT, MADE OF HEAVY DUTY NYLON MATERIAL

Carburetor Rebuild Tools

Portable 12V Chainsaw Sharpener for on the job use. Comes with a 5/32", 3/16", & 7/32" grinding stone. Extra grinding stones available for purchase as well.

ELECTRONIC DIGITAL TACHOMETER FOR ALL 2 CYCLE CHAIN SAWS AND AIR COOLED ENGINES, YOU CAN CHOOSE BETWEEN 2 CYCLE OR 4 STROKE ENGINES TO PROPERLY SET THE RPM'S OF YOUR ENGINE SPEED ON YOUR CHAIN SAW, TRIMMER, BLOWER, HEDGE TRIMMER OR GASOLINE 4 STROKE ENGINE. THIS IS A HIGH QUALITY ELECTRONIC ENGINE TACHOMETER. MADE IN USA

A HIGH QUALITY ETHANOL GASOLINE TESTER
ALL CHAIN SAWS, EASY TO USE AND DETERMINE HOW MUCH ETHANOL IS IN YOUR GASOLINE.

GRAY SILICONE FOR SEALING CYLINDERS TO CRANKCASES, CRANKCASE HALVES. NOTE RECOMMENDED FOR SEALING FUEL TANKS

Ignition & Spark Plug Tester

High Quality Chain-Sharpening Stump Vice.

THIS IS A HIGH QUALITY SPARK TESTER TO TEST THE STRENGTH AND RESERVE CAPACITY OF THE IGNITION COIL, ADJUST THE GAP TO 4MM BY TURNING THE SCREW ON THE TESTER, IF YOU HAVE SPARK, THE COIL IS GOOD, TO TEST THE LOAD CAPACITY TURN TO 6MM OUT AND CHECK THE SPARK. IF YOU HAVE SPARK THE RESERVE OF THE COIL IS 20% ABOVE AND THE COIL IS GOOD.

MEDIUM DUTY THREAD LOCK, WILL HELP KEEP THE BOLTS FROM VIBRATING LOOSE. FOR USE ON CHAIN SAWS, TRIMMERS, BLOWERS AND OUTDOOR POWER EQUIPMENT, COLOR BLUE

HEAVY DUTY THREADLOCKER FOR USE ON ALL CHAIN SAWS, WILL HELP KEEP THE SCREWS TIGHT FROM VIBRATION, COLOR RED, HIGHLY RECOMMENDED FOR CHAIN SAWS, TRIMMERS, BLOWERS AND OUTDOOR POWER EQUIPMENT

LOCTITE ANAEROBIC GASKET MAKER, RECOMMENDED FOR USE ON CYLINDERS GASKETS TO ENSURE PROPER SEALING AND OTHER GASKETS, CAN BE USED WITHOUT GASKETS

High Quality Oregon Chainsaw Chain Sharpener.

High Quality Ring Compression Release.

High Quality Ring Compression Release.

PRESSURE-VACUUM TEST KIT, FOR PRESSURE TESTING 2-CYCLE ENGINES FOR AIR LEAKS, COMES WITH A VERY HIGH QUALITY VACUUM-PRESSURE TESTER IN A PLASTIC CASE, RUBBER BLOCK OFFS AND A SPECIAL ADAPTER TO SCREW INTO THE SPARKPLUG HOLE TO PERFORM THE TEST. NOTE: THE SPARK PLUG ADAPTER IS 14MM X 1.25MM THREAD PITCH, VERIFY THAT YOU HAVE THIS SIZE, 10MM ADAPTOR IS BEING MADE AND WILL BE ADDED LATER ONCE IN STOCK

Bar Tip Grease Gun

Suitable Replacement Grindstone For Chainsaw Sharpeners.

SPARK IGNITION TESTER
ALL CHAIN SAWS THAT HAVE A SPARK PLUG WIRE, EASY TO USE, ACCURATE

A HIGH QUALITY SPARK PLUG GAP GAUGE FOR ADJUSTING THE PROPER SPARK PLUG GAP FOR PEAK PERFORMANCE

SPARK PLUG THREAD CLEANER THREAD CHASER, WILL REPAIR DAMAGE THREADS FROM PLUGS THAT HAVE CROSS THREADED IN THE SPARK PLUG HOLE. THIS IS A HIGH QUALITY THREAD CLEANER MADE IN THE USA

HEAVY DUTY STAINLESS STEEL FUEL LINE PINCH OFF FORCEPS, FOR USE ON WORKING ON CHAIN SAWS, TRIMMERS, BLOWERS AND OUTDOOR POWER EQUIPMENT. A EXCELLANT TOOL FOR STOPPING THE FLOW OF GASOLINE WHEN WORKING ON CARBURETORS

High Quality Chain Sharpener.

HEAVY DUTY FLYWHEEL PULLER FOR USE ON WORKING ON CHAIN SAWS, TRIMMERS, BLOWERS AND OUTDOOR POWER EQUIPMENT. A EXCELLENT TOOL FOR REMOVING FLYWHEELS ON MOST CHAINSAW. NOTE: WILL NOT WORK ON ALL CHAINSAWS, YOUR FLYWHEEL WILL NEED THREADED HOLES FOR THE BOLTS TO SCREW INTO, YOU MAY NEED TO REMOVE THE STARTER PAWLS TO GAIN ACCESS TO THE THREADED HOLES IN THE FLYWHEEL